Hello, I have always used a modem/router until I bought a EA6700. I now have my Billion 7800N (as pure bridge with DHCP disabled) sitting behind my new router. I am able to get on to the internet through the router. My modem ip is 192.168.1.254 (default ip) and my router ip is 192.168.2.1. My home L

Nov 19, 2018 · When the mode is enabled, the MOFI is like a modem and whatever WAN address is assigned by the carrier is assigned to the device on LAN 1. You can setup the MOFI in bridge mode using the IP Passthrough/Bridge configuration page. Nov 29, 2017 · When I try to log into my modem using the IP address it just gives me a web page saying its unable to connect. My internet works fine, I am able to ping the address and it replies with no data loss, I can trace route to it, I can release and renew the IP address DHCP server. The modem itself doesn’t know how to route to anything, so we need to punch another hole in the firewall to make this happen. This is a bit of a hack as we need to hardcode NTP IP addresses in Select IP Passthrough below the Firewall tab. Enter the Device Access Code if prompted. Select the Default Server option from the Allocation Mode drop-down menu. Enter the IP address of the Device to be set as the default server in the Default Server Internal Address field. Select Save. A re-starting gateway reminder message appears.

Mar 29, 2017 · By default, your NETGEAR router's IP address is either 192.168.1.1 or 192.168.0.1. The computer or mobile device that you are using automatically retrieves the IP address from your router. If your computer or mobile device is using a static IP address, you need to configure your device to retrieve the IP address. To view your router's IP address:

Dec 18, 2019 · IP addresses that start with 10 default to a different subnet scheme. Here, the subnet is defined simply by the first number. A subnet mask, of 255.0.0.0. indicates this. Any IP address that starts with 10 would be valid (10.1.2.3, 10.4.5.6, 10.199.198.197, etc). A Static IP Address is an IP Address that is associated with your account that never changes and can be assigned to a specific device. Every time that you connect to the AT&T Network the Static IP address will route traffic to the computer or other device that can be assigned an IP address (such as a Router or Firewall). The simplest method to reset your public and private IP address is by Power Cycling your router and if there is a modem, then the modem too. To do this, power both the devices off, wait for ten minutes and turn them back on. Most cable modems come with a battery back up, so if powering off doesn’t completely power off, then take the batteries Mar 29, 2017 · By default, your NETGEAR router's IP address is either 192.168.1.1 or 192.168.0.1. The computer or mobile device that you are using automatically retrieves the IP address from your router. If your computer or mobile device is using a static IP address, you need to configure your device to retrieve the IP address. To view your router's IP address:

Dec 26, 2019 · [LAN] How to set up Static Route . 1. Enable static routes choose Yes.. 2. Network/ Host IP: It stands for the destination network or host of a route rule so it should be a host address, such as "192.168.123.11" or a network address, such as "192.168.0.0".

Mar 29, 2017 · By default, your NETGEAR router's IP address is either 192.168.1.1 or 192.168.0.1. The computer or mobile device that you are using automatically retrieves the IP address from your router. If your computer or mobile device is using a static IP address, you need to configure your device to retrieve the IP address. To view your router's IP address: Nov 19, 2018 · When the mode is enabled, the MOFI is like a modem and whatever WAN address is assigned by the carrier is assigned to the device on LAN 1. You can setup the MOFI in bridge mode using the IP Passthrough/Bridge configuration page. Nov 29, 2017 · When I try to log into my modem using the IP address it just gives me a web page saying its unable to connect. My internet works fine, I am able to ping the address and it replies with no data loss, I can trace route to it, I can release and renew the IP address DHCP server. The modem itself doesn’t know how to route to anything, so we need to punch another hole in the firewall to make this happen. This is a bit of a hack as we need to hardcode NTP IP addresses in